Seanav Marine
Bearing Pelorus Alignment Specialists SOLAS Chapter V Reg 19.2.5 Compliant Synchro, Stepper & NMEA 0183 HDU 24/7 Port & Anchorage Dispatch

Marine Gyro Repeater Repair, Bearing Pelorus Alignment & Heading Distribution in India

Seanav Marine is India’s foremost technical authority for commercial shipboard Marine Gyro Repeaters and Heading Transmission Systems, providing emergency repairs, bridge wing pelorus optical alignments, damper fluid renewals, and Heading Distribution Unit (HDU) multi-channel isolation across all Indian major ports and anchorages.

⚓ Official Operational Scope & National Capabilities

Seanav Marine delivers certified Marine Gyro Compass Repeater repair, bridge wing pelorus stand alignment, analogue and digital steering repeater calibration, synchro-to-step heading transmission overhauls, and Heading Distribution Unit (HDU) multi-channel isolation across all 400+ Indian commercial ports and anchorages (JNPT / Nhava Sheva, Mumbai, Kandla, Mundra, Cochin, Chennai, Visakhapatnam, Paradip, Haldia, Mormugao, Mangalore, Tuticorin). Servicing Sperry Marine (Navigat / SR-120), Tokyo Keiki (TG-8000 / TG-6000 / PR-9000), Yokogawa (CMZ-900 / CMZ-700), Raytheon Anschütz (Standard 22 / Horizon), and Simrad systems, our certified marine electronics engineers board 24/7 with optical alidades, synchro test sets, and digital NMEA heading analyzers to resolve repeater drift, frozen dials, 180-degree phase inversions, and step transmission lag compliant with SOLAS Chapter V Regulation 19.2.5.1-3 and IMO Resolution A.424(XI).

⚙️ Technical Specifications & Operational Coverage

Supported Systems Sperry Marine (Navigat 100 / 200 / SR-120), Tokyo Keiki (TG-8000 / TG-6000 / MBT Series), Yokogawa (CMZ-900 / CMZ-700 / MKR Series), Raytheon Anschütz (Standard 22 / Horizon), Simrad (AR80 / AR78 / GC80), Alphatron Marine
Repeater Hardware Bridge Wing Weatherproof IP56/IP67 Bearing Repeaters, Wheelhouse Centre Steering Repeaters, Emergency Steering Flat Repeaters, Digital 4-Digit Heading Displays, Course Recorders
Transmission Modes DC Step-by-Step (24V–70V DC, 6 steps/degree), Synchro Telemetry (1:1, 36:1, 90:1, 360:1 gear ratios, 115V AC 400Hz / 50-60Hz), Serial NMEA 0183 ($HEHDT, $THS at 4800 / 38400 bps), IEC 61162-2
Optical Instruments Prism Azimuth Circles (Model 1137 / 1138), Optical Telescopic Alidades, Gimbaled Pelorus Deck Stands, Bulkhead Mounting Brackets, Anti-Vibration Dampers
Regulatory Mandate SOLAS Chapter V Regulation 19.2.5.1, 19.2.5.2, 19.2.5.3, IMO Resolution A.424(XI), ISO 8728, DGS Indian Maritime Rules
Attendance SLA Within 2 hours to berths at JNPT/Mumbai, Kandla, Mundra, Cochin, Chennai, Vizag, Paradip; 3-4 hours to outer anchorages via pilot launches

🏷️ Supported OEM Brands & Equipment

Our engineers are equipped with manufacturer diagnostic keys, test software, and genuine spare parts for leading bridge electronics manufacturers:

Furuno Radars, AIS FA-170, FMD ECDIS, VR-7000 VDR
JRC JMR-9200, JHS-183 AIS, JAN-9201, JCY-1900
Sailor / Cobham 6000 GMDSS, 6222 VHF, 6300 MF/HF
Tokyo Keiki TG-8000 Gyro, PR-9000 Autopilot
Sperry Marine VisionMaster FT, Navigat 100/200
Yokogawa CMZ-900 Gyro Compass
Raytheon Anschütz Synapsis ECDIS, Standard 22 Gyro
Danelec Marine DM100 VDR & S-VDR, DM800 ECDIS
Jotron Tron 40S / 60S 406 MHz EPIRB, SART
Samyung ENC AIS SI-30, VHF STR-6000A, EPIRB

📋 Standard 5-Step Marine Gyro Repeater Overhaul & Pelorus Alignment SOP

  1. Step 1: Master Gyro Heading Transmission Signal & Serial NMEA / Stepper Voltage Audit

    Measure DC step voltages and AC synchro reference voltages across transmission bus terminals. Inspect serial NMEA 0183 ($HEHDT, $THS) sentence integrity, baud rates, and update frequency using digital signal analyzers to eliminate transmission noise.

  2. Step 2: Bridge Wing Bearing Repeater Pelorus Stand Fore-and-Aft Optical Alignment

    Check physical alignment of bridge wing pelorus stand lubber line against vessel true fore-and-aft centerline. Use optical transit sights to zero index error, tighten gimbal locking screws, replenish silicon damper fluid, and verify 360° unobstructed horizon sightlines.

  3. Step 3: Steering Repeater Synchro / Stepper Motor Backlash & Damper Fluid Calibration

    Inspect mechanical gear trains, internal stepper drive motors, and viscous damping fluid pots on wheelhouse steering and emergency steering repeaters. Eliminate mechanical gear backlash, replace hardened o-rings, and verify smooth, deadbeat compass card settling.

  4. Step 4: Heading Distribution Unit (HDU) Multi-Channel Isolation & Optical Repeater Synchronization

    Test opto-isolated output channels on Heading Distribution Unit (HDU). Verify individual channel circuit breakers, prevent ground fault cross-talk to Radar, ECDIS, and Autopilot, and electronically synchronize all repeater cards to master gyro true north.

  5. Step 5: Azimuth Circle & Terrestrial Bearing Alignment Verification

    Mount type-approved prism azimuth circle on bearing repeater bowl. Take optical sights on known terrestrial landmarks or celestial objects, calculate optical index error, verify 0.1° compass card repeatability, and issue Seanav Technical Calibration Certificate.

🔍 Critical Marine Gyro Repeater Failures & Deficiencies Resolved at Indian Ports

Reported Defect Root Cause Diagnosis Technical Remediation
Bridge Wing Bearing Repeater Heading Lag & Stepper Motor Slip Worn stepper motor drive gears, degraded electrolytic capacitors on repeater amplifier PCB, or high-resistance terminal connections on bridge wing junction boxes. Renewal of stepper motor assembly, PCB capacitor re-capping, terminal re-crimping with moisture-proof heat shrink, and re-synchronization to master heading.
Steering Repeater Phase Reversal & 180° / 90° Heading Inversion Incorrect S1/S2/S3 synchro stator wiring phase sequence or inverted R1/R2 rotor reference excitation after shipyard rewiring or panel replacement. Phase sequence diagnostic verification using synchro phase meter, correction of stator winding taps, and validation of compass rose rotation sense.
Heading Distribution Unit (HDU) Output Isolation Fuse Failure / Signal Loss to Radar/ECDIS Short circuit on external bridge wing repeater cable blowing individual channel buffer fuse, dropping heading serial feed to navigation bridge sensors. Channel isolation fault tracing, blown fuse and optocoupler replacement, insulation resistance Megger testing, and restoration of independent sensor heading lines.
Bearing Pelorus Weatherproof Seal Failure, Condensation & Internal Corrosion Hardened or cracked perimeter rubber gasket on IP56/IP67 repeater bowl, allowing sea spray and tropical monsoon moisture to corrode dial illumination and synchro. Complete internal desiccation, renewal of marine neoprene sealing gaskets, replacement of dimmer potentiometer and LED lamps, and nitrogen dry-air purge.
Verified Indian Port Attendance Case Study

Emergency Bridge Wing Bearing Repeater Alignment & Synchro Distribution Repair on 175,000 DWT Capesize Bulk Carrier at Paradip Port

Vessel Type 175,000 DWT Capesize Iron Ore Carrier
Equipment Scoped Tokyo Keiki TG-8000 Gyro Compass & Dual Bridge Wing Pelorus Bearing Repeaters
Port & Berth Paradip Port Authority (PPT), Odisha - Iron Ore Berth

Reported Problem: Port bridge wing bearing repeater frozen during loading operations; Starboard pelorus showing 4.2° misalignment against master compass, threatening Port State Control detention before sailing for China.

Technical Diagnosis: Seized stepper drive motor on port repeater due to salt air ingress; slipped gimbal lock screw on starboard pelorus stand causing physical index line deflection.

Corrective Attendance: Attended Paradip Iron Ore Berth within 3 hours. Replaced port repeater stepper drive motor and desiccating breathing valve from Seanav spares inventory; re-machined gimbal index pin on starboard stand; performed precision transit optical alignment against shore navigation landmark to verify 0.0° index error.

✓ Operational Outcome: Both bridge wing bearing repeaters synchronized to master compass within 0.1°. PSC inspection passed with zero findings; vessel sailed on high water without tidal demurrage.

🌐 Strategic Indian Port & Equipment Authorities

Explore specialized technical resources and 24/7 engineer coverage across key Indian shipping hubs:

🛡️ Verified Maritime Technical Authority Technical Review: October 2026

Reviewed & Certified by Technical Operations Directorate

Lead Marine Electronics Surveyor & Technical Director · Seanav Marine

Master technical oversight for SOLAS Chapter IV & V navigational safety and radio communications. Certified in statutory marine radio surveys, gyro compass meridian calibrations, radar transceiver overhauls, and VDR APT protocols across 170+ commercial Indian ports and anchorages.

📜 DG Shipping / WPC Maritime Radio General Operator (GOC) 🧭 MCA Approved Magnetic Compass Adjuster 📋 SOLAS Chapter IV & V Statutory Compliance Lead 🔧 OEM Factory-Trained Engineers (Furuno, JRC, Sperry, Tokyo Keiki, Danelec)

❓ Frequently Asked Questions

Under SOLAS Chapter V Regulation 19.2.5.1-3, all ships of 500 gross tonnage and upwards must be fitted with a gyro compass or other means to determine heading and transmit heading information to the steering position, emergency steering position, and bridge wing bearing positions (pelorus stands) across 360 degrees of the horizon.

Bridge wing repeaters are exposed to harsh salt spray, UV degradation, and temperature swings. Freezing or lagging is usually caused by ingress of moisture seizing internal stepper motors, dried viscous damping fluid, corroded slip rings, or voltage drop along long cable runs from the master compass.

We utilize precision optical alidades and transit lines sighted onto the ship's jackstaff, foremast, or shore landmarks with known azimuths. The pelorus mounting base and gimbal lubber lines are mechanically adjusted to align parallel with the ship's centerline, ensuring zero parallax or mechanical index error.

Yes. We supply and install type-approved Gyro Heading Converters (step-to-NMEA and synchro-to-NMEA) that sample high-voltage analogue signals and generate high-speed, opto-isolated serial sentences ($HEHDT, $THS at up to 50 Hz) for ECDIS, Radar, VDR, and AIS integration.

Yes. We stock complete analogue and digital bearing repeaters, steering repeaters, pelorus deck stands, azimuth circles, damper pots, stepper motors, and Heading Distribution Unit (HDU) driver PCBs at our Navi Mumbai warehouse, Chennai base, and Gujarat port depots for immediate emergency dispatch.